Ducati Scrambler 800 - Service manual > Parameter setting/displaying

Upon key-on, the instrument panel:

• turns on the display backlighting;
• activates the rev counter which increases from 0 to 12000 and decreases back to 0;
• activates the vehicle speed digits and shows a counting from 0 to 300 and then back to 0;
• turns on the warning lights from right to left.

At the end of the check, the instrument panel displays the main screen ("standard screen") showing the available functions and turns on the warning lights, if necessary.

During this first check stage, if the motorcycle speed exceeds 20 km/h (12 mph) (actual speed), the instrument panel will stop:

• the display check routine and display the standard screen containing updated information;
• the warning light check routine and leave ON only the warning lights that are actually active at the moment.

Data displayed on the main screen are as follows:

1. Engine speed.
2. Motorcycle speed.
3. MENU 1 (Odometer, Trip 1, Trip 2, Trip Fuel, Air temperature, Error warning - only if active).
4. Clock.
5. SERVICE indication (only if active).
6. Setting menu.
7. Side stand status.

From the main screen, press button (2) on LH switch to view Menu 1 information.

• Odometer (TOT);
• TRIP 1;
• TRIP 2;
• TRIP FUEL (when function is active);
• T - AIR.

The instrument panel stores Menu 1 settings in use upon KEY-OFF. On the following KEY-ON, previously stored Menu 1 pages are displayed.

In case of sudden and unexpected power OFF, the instrument panel displays the default settings upon the following KEY-ON:

• Menu 1 default page = Odometer (TOT).

Upon KEY-ON, for every display layout, instrument panel shows for 10 seconds in Menu 1 the "Odometer" page and then shows the page saved upon previous KEY-OFF.

Hold the button (2) for 3 seconds, when actual motorcycle speed is <= (lower than or equal to) 20 km/h (12 mph), to enter the Setting Menu, where you can set any function.

Important You can enter the SETTING MENU only if vehicle actual speed is <= (lower than or equal to) 20 km/h (12 mph). Within the SETTING MENU, if vehicle actual speed exceeds 20 km/h (12 mph), the instrument panel automatically quits the menu and shows the Standard Screen.

Function buttons

1) UP CONTROL SWITCH

Button used to display and set instrument panel parameters with the position

2) DOWN CONTROL SWITCH

Button used to display and set instrument panel parameters with the position.

3) HIGH-BEAM FLASH BUTTON (FLASH)

This button is the high-beam flasher.

4) TURN INDICATORS CANCEL BUTTON

The turn indicators cancel button may also be used for the CONFIRM MENU function, for selecting the riding mode. Push this button for 3 seconds to the left side to activate the "Hazard" function (all 4 turn indicators).

Technological Dictionary

Anti-lock Braking System (ABS) 9M

ABS 9M system is a two-channel latest-generation system that actuates combined braking with anti lift-up function for the rear wheel so as to guarantee not only a reduced stopping distance, but also a higher stability under braking.

Acronyms and abbreviations used in the Manual

ABS
Antilock Braking System
CAN
Controller Area Network
DDA
DUCATI Data Acquisition
DSB
Dashboard
ECU
Engine Control Unit

Instrument panel

1) LCD.

2) REV COUNTER (rpm).

It indicates engine rpm value.

3) NEUTRAL LIGHT N (GREEN).

Comes on when in neutral position.

4) HIGH BEAM LIGHT

(BLUE).

It turns on to indicate that the high beam lights are on and when the flasher is activated.

5) ENGINE OIL PRESSURE LIGHT

(RED).

Comes on when engine oil pressure is too low. It must turn on at "KEY-ON", but must turn OFF a few seconds after the engine has started. It may shortly come on when the engine is hot, however, it should go out as the engine revs up.

Important If the ENGINE OIL light stays ON, stop the engine or it may suffer severe damage.

6) FUEL WARNING LIGHT

(AMBER YELLOW).

Comes on when fuel is low and there are about 4 litres (1.06 gallons) of fuel left in the tank.

7) TURN INDICATOR LIGHTS

(GREEN).

A warning light turns on and blinks when the relevant turn indicator is active; when the warning lights blink at the same time, the HAZARD function is active.

8) "ENGINE/VEHICLE DIAGNOSIS - EOBD" LIGHT

(AMBER YELLOW).

It turns on in the case of "engine" and/or "vehicle" errors and in some cases will lock the engine.

9) ABS LIGHTS

(AMBER YELLOW).

This turns on to indicate that ABS is disabled or not functioning.

10) OVER REV / IMMOBILIZER / ANTI-THEFT SYSTEM (RED)

Note Each calibration of the Engine Control Unit may have a different setting for the thresholds that precede the rev limiter and the rev limiter itself.

SW update

The DSB software can be updated through the DUCATI diagnosis instrument, which uses a suitable dedicated KWP2000 communication protocol.

See also: