Ducati Scrambler 800 - Service manual > Odometer (TOT)

The odometer counts and displays the total distance covered by the motorcycle with the set unit of measurement (km or mi).

The odometer number (in km or miles) is displayed with the message TOT and the indication of the unit of measurement.

When the maximum value is reached (199999 km or 199999 mi) the instrument panel will permanently display said value.

The odometer value is saved permanently and cannot be reset under any circumstances.

The reading is not lost in case of a power OFF (Battery OFF).

Note Upon Key-ON, the instrument panel always shows the Odometer indication for 10 seconds, then shows the user's settings page.

Note If a string of flashing dashes " ----- " is displayed within odometer function, please contact a Ducati Dealer or Authorised Service Centre.

Odometer Update

The DUCATI diagnosis instrument allows performing a series of activations to check some instrument panel functions and resetting parameters or warning lights. After each activation, the instrument panel will restore its standard functions.

Note The activations must be performed only with key turned to ON, engine off and battery voltage ≥ 11.0 V.

This function allows copying the km value saved in the odometer when replacing the instrument panel or the engine control unit (ECU).

When replacing the instrument panel or the engine control unit (ECU), it is necessary that the authorised dealer copies (*) the km value to the new control unit using the DDS Diagnosis Instrument.

Until this procedure is performed, the instrument panel display will show some flashing dashes "-----" instead of the Odometer value.

The procedure is successfully completed when the display shows the odometer value. (*): for the "procedure" to be followed with the DDS instrument to be added in the Workshop Manual, contact the SERVICE.

Menu 1 functions

MENU 1 functions are:

• Odometer (TOT);
• Trip meter 1 (TRIP 1);
• Trip meter 2 (TRIP 2);
• Partial fuel reserve counter (TRIP FUEL);
• Ambient air temperature (T-AIR).

By pressing button (2) it is possible to view the functions of MENU 1.

Engine rpm indication (RPM)

This function allows displaying engine rpm.

Instrument panel receives rpm value and displays it.

The information is displayed by the bargraph filling from the right to the left according to the engine rpm.

The thresholds before the rpm limiter are: 1st threshold 8900 rpm (A).

When the rev limiter value (B) is reached, the warning lights start flashing.

Activations through diagnosis instrument

The DUCATI diagnosis instrument allows performing a series of activations to check some instrument panel functions and resetting parameters or warning lights. After each activation, the instrument panel will restore its standard functions.

Note The activations must be performed only with key turned to ON, engine off and battery voltage ≥ 11.0 V.

This activation allows checking for instrument panel malfunctions or display problems of the rpm indication.

Upon receiving this input the instrument panel shows for 5s the following values in sequence:

• ' 1000 rpm '
• ' 5000 rpm '
• ' 11000 rpm '.

Motorcycle speed

This function allows displaying the vehicle speed (km/h or mph according to the specific application).

The instrument panel receives information about the actual motorcycle speed (calculated in km/h) and displays the value increased by 5% and converted in the set unit of measurement (km/h or mph).

The max. displayed speed is 299 km/h (186 mph).

A string of dashes "- - -" is displayed with the set unit of measurement if:

• speed is higher than 299 km/h or 186 mph or if instrument panel is not receiving the speed value ("- - -" steady ON);
• the rear speed sensor is in fault (flashing "- - -").

Activations through diagnosis instrument

The DUCATI diagnosis instrument allows performing a series of activations to check some instrument panel functions and resetting parameters or warning lights. After each activation, the instrument panel will restore its standard functions.

Note The activations must be performed only with key turned to ON, engine off and battery voltage ≥ 11.0 V.

This activation allows checking for instrument panel malfunctions or display problems of the speed indication.

Upon receiving this input the instrument panel shows for 5s the following values in sequence:

• ' 50 km/h '
• ' 100 km/h '
• ' 299 km/h '.

Main functions

The functions displayed in the Standard screen are the following:

Main information

• Vehicle speed
• Engine rpm indication (RPM)
• Menu 1 displays the following functions:

1. Odometer (TOT)
2. Trip meter 1 (TRIP 1)
3. Trip meter 2 (TRIP 2)
4. Partial fuel reserve counter (TRIP FUEL)
5. Ambient air temperature (AIR)
6. Clock

Additional information

• Service indication (SERVICE)
• ERROR indication

The functions within the Setting Menu that can be modified by the user are the following:

• PIN CODE (activation and modification of PIN CODE);
  CLOCK (clock settings);
  LIGHT (backlighting settings);
  BATTERY (battery voltage indication);
  UNITS (units of measurement settings);
  ABS (ABS control unit enabling/disabling);
  EXIT (to quit the Setting Menu).

See also: