Moto Guzzi V85 TT - Service manual > Battery

REMOVAL

• Remove the glove compartment
• Undo and remove the screw (1)
• Remove the negative cable from the battery (2)
• Refit the screw (1) along with the yoke in the specific seat

• Lift the protective boot (3)
• Undo and remove the screw (4)
• Remove the positive cable (5)
• Refit the screw (4) along with the yoke in the specific seat

• Remove the battery (6)

Tail guard

REAR FAIRINGS REMOVAL

• Remove the luggage rack
• Unscrew and remove the screws (1)
• Unscrew and remove the screws (2)

• Remove the rear fairing (3)

• Undo and remove the screw (4)

• Remove the right rear fairing (5)

• Undo and remove the screw (6)

• Remove the left rear fairing (7)

Copertura terminale

REMOVAL

• Unscrew and remove the screws (1)

• Remove the left cover (2)

• Unscrew and remove the screws (3)

• Remove the terminal cover (4)

• Retrieve the washers (5)

Pre-delivery

Specific operations for the vehicle

WINDSHIELD KIT ASSEMBLY

• The box containing the windshield is in the vehicle packaging. The installation hardware is mounted on the windshield bracket assembled to the vehicle
• Installation begins with the removal of the mounting hardware from the windshield bracket (for each of the four fastening points, made up of: rubber piece, bushing and screw)
• Subsequently, the four rubber pieces (1) are fitted in the respective holes on the windshield, avoiding the use of tools that can damage or scratch the component
• The bushings (2) should be inserted in the holes of the rubber pieces from the front side of the windshield
• The windshield should then be rested on the relative bracket on the vehicle and, supporting it firmly, the screws should be fastened (3), tightening them to the torque indicated on the chart

WINDSHIELD KIT TIGHTENING TORQUES

HANDGUARDS AND REAR VIEW MIRRORS

KIT ASSEMBLY

• The box containing the right and left handguards, the anti-vibration weights and the hardware required for assembling the aforementioned components is in the vehicle packaging
• There is also a box containing the rear view mirrors
• Installation of the handguards begins with the insertion of the rubber piece (1) in the specific cylindrical lodging on the internal side of the handguards.
• Then, rest the anti-vibration weight (2) in correspondence to the end of the handlebar and on this handguard (3), taking care to line up the inside with the shape of the anti-vibration weight; then, the "T" bushing (4) should be inserted on the handguard and the screw (5) inserted without tightening it all the way.
• Then, insert the other "T" bushing from below on the second handguard fastening hole and screw in the rear view mirror (6)
• Then, tighten the screw (5), observing the tightening torque indicated on the attached chart
• Repeat the same procedure to mount the handguard/rear view mirror on the opposite side

HANDGUARDS/REAR VIEW MIRRORS KIT TIGHTENING TORQUES

BATTERY COVER ASSEMBLY

• Remove the saddle, acting on the lock positioned on the licence plate holder and lift it from the rear part, unhooking it from its lodgings in correspondence to the fuel tank
• Remove the screws (1) and extract the battery cover (2) from the front lodgings, sliding it toward the rear
• Place the battery in the appropriate lodging and connect it, taking care to observe the polarity
• Refit the battery cover, inserting it in the appropriate lodgings as indicated in figure "C"
• Insert the screws (1) in the appropriate holes, observing the tightening torque indicated on the attached chart
• Refit the saddle, hooking it in the front part in the appropriate lodgings in correspondence to the fuel tank and lower it at the rear, ensuring that the saddle lock has clicked.

BATTERY COVER KIT TIGHTENING TORQUES

See also: